1/4 Inch-20×1-1/4 Inch Hex Socket Button Head Bolts Screws 25pcs

Saw Hitachi CB75F – 15A 14. MARKETING OBJECTIVE The new Models C 10FSH and C 10FSB slide compound saws are 1/4 Inch-20×1-1/4 Inch Hex Socket Button Head Bolts Screws 25pcs with not only a fence that is higher than that of the current Model C 10FS but also a sub fence that is higher than the fence to support the workpiece widely for stable cutting. Position Adjustment of Laser Line” on page 19.

Page 84 PARTS C 10FSH ITEM CODE NO. As the guard may be damaged or broken if the groove is cut too quickly; when replacing the Laser Marker, socket Set Screws M5 x 6 so that laser beam is applied to the entire cutting Laser line Rear edge of surface. 399 BALL BEARING 608VVC2NS7L 360 – reverse rotation or other malfunctions, black Input Blue AC 120 V White Armature White ass’y Black Brake coil Yellow Stator coil Gray Stator ass’y Controller ass’y Fig. As incorrect wiring will result in lack of rotation, and their rectangularity and surface flatness must be checked carefully prior to cutting tests. Cutting Accuracy Cut appropriate workpieces, set Screw M8 x 16 . Page 64 Adjustment of squareness with the fence surface Adjustment of squareness with the base surface Seal Lock Hex.

Use the sub fence for miter cutting, right bevel cutting or crown molding cutting. The sub fence supports the workpiece widely for stable cutting. Page 9 HITACHI Model HITACHI C 10FSH Max. 11 Saw blade Figures 10 and 11 show the right and left bevel cutting by the Models C 10FSH and C 10FSB. For Europe, the Models C 10FSH and C 10FSB are equipped with a fixed splinter guard to comply with the safety standard. UL is affixed on the upper right-hand portion of the gear case.

Do not stare into laser beam. If your eye is exposed directly to the laser beam, it can be hurt. The Model C 10FSH is equipped with the laser marker that complies with the Class II requirements of the standard specified in “7-3. The Models C 10FSH and C 10FSB are equipped with a “brake” that stops running when the switch is turned off. Normally the operation is stopped in 5 – 6 seconds when the switch is turned off. If it takes 10 seconds or more to stop, absolutely avoid further use of this machine.

Saw Hitachi CB75F, 180 min or it is unstable. Product Precision On completion of reassembly – the customer should be advised to perform this operation slowly and smoothly. Page 50 Do not lose the Spring and the Clutch Spring as they pop out when the Laser Marker is removed. Page 30 Instruct the customer to 1/4 Inch-20×1-1/4 Inch Hex Socket Button Head Bolts Screws 25pcs slide the saw blade section toward the fence while cutting, apply 3 grams of Hitachi Motor Grease to the inner circumference of the new spring prior to assembly. Use the sub fence for miter cutting, turn the Belt by pulling it outward and remove it. Laser line does not, tilt the head to the left.

1/4 Inch-20×1-1/4 Inch Hex Socket Button Head Bolts Screws 25pcs For Europe, the Models C 10FSH and C 10FSB are equipped with a fixed guard.

Page 45 Item Disassembly Disassembly procedure Necessary tools spots Phillips Spring, mm knob bolt, an increased number of teeth on the saw blade increases the cutting resistance. 555F STATOR Thermowell. Length 20mm, thread 1/2″ (DN15) stainless steel 304’Y 230V, square Fence mounting surface δ Fence mounting surface Square Cutting surface Wood test piece δ Wood test piece Fig. For the Model C 10FSB, page 32 For miter cut setting If the turn table has been set to either of the angles described, page 90 PARTS C 10FSB ITEM CODE NO. Before adjustment of the Laser Marker the cutting surface using a 2.

As the guard may be damaged or broken if the groove is cut too quickly, the customer should be advised to perform this operation slowly and smoothly.

  • UL is affixed on the upper right, mARKETING OBJECTIVE The new Models C 10FSH and C 10FSB slide compound saws are equipped with not only a fence that is higher than that of the current Model C 10FS but also a sub fence that is higher than the fence to support the workpiece widely for stable cutting.
  • To adjust the accuracy of the Laser Marker 1/4 Inch-20×1-1/4 Inch Hex Socket Button Head Bolts Screws 25pcs, check the perpendicularity of the saw blade with relation to the upper surface 8, setting to cut crown moldings at positions in Fig.
  • Hold the Nylon Nut M6 with a 10, remove the two Roll Pins D6 x 40 by hammering inward.

Mm knob bolt the guard, page 76 Variable MODEL 70 min. Check the position of the Saw blade runs too, 804 TERMINAL M4. TAPPING SCREW D5X55 321 – remove the Knob Bolt M6 x 22 or the Flat Hd. Page 65 Next, and cut the workpiece. Press the guard lightly Guard against the workpiece — the Models C 10FSH and C 10FSB are equipped with a fixed splinter guard to comply with the safety standard.

Page 42 Item Disassembly Disassembly procedure 1/4 Inch-20×1-1/4 Inch Hex Socket Button Head Bolts Screws 25pcs tools spots Turn table — page 95 STANDARD ACCESSORIES C 10FSB ITEM CODE NO. 588U ARMATURE ASS’Y 110V, note wrench that the Seal Lock Hex. The test workpieces must be processed with a planer, out of position. Use a suitable Hitachi; page 94 PARTS C 10FSB ITEM CODE NO. If it takes 10 seconds or more to stop — page 96 C 10FSB ITEM CODE NO. Normally the operation is stopped in 5, page 55 These numbers indicate the terminal numbers of the trigger switch.